H3c-technologies H3C WX5500E Series Access Controllers Manuale Utente

H3C WX5540E Access ControllerInstallation Guide Hangzhou H3C Technologies Co., Ltd. http://www.h3c.com Document version: AW101-

4 • Always wear an ESD-preventive wrist strap. Make sure the wrist strap makes skin contact and is well grounded when installing the transceiver mod

5 • Use electromagnetic shielding, for example, shielded interface cables, when necessary. Lightning protection To better protect the device from li

6 Item Requirements Result ESD prevention • The equipment and rack are well grounded. • The equipment room is dust-proof. • The humidity and tempe

7 Installing the access controller WARNING! Keep the tamper-proof seal on a mounting screw on the chassis cover intact, and if you want to open the

8 Installation flow Figure 3 Installation flow Mounting the device on a workbench If a standard 19-inch rack is not available, you can place a dev

9 Figure 4 Mounting the device on a workbench Installing the device in a 19-inch rack You can install the device in a 19-inch rack by using the fol

10 Installing the device by using front and rear mounting brackets 1. Wear the ESD-preventive wrist strap and make sure the rack is well grounded an

11 Figure 9 Installing the weight-bearing screws 5. Determine the device installation position in the rack and use screws and cage nuts to attach

12 Figure 11 Installing the device to the rack NOTE: After pushing the device into the rack, make sure the upper edges of the rear mounting brack

13 Figure 12 Installing the rack shelf 4. Push the device to the rack along the rack shelf, and attach the front mounting brackets on the device t

Copyright © 2013, Hangzhou H3C Technologies Co., Ltd. and its licensors All rights reserved No part of this manual may be reproduced or transmitted

14 To install the device by using front mounting brackets and slide rails: 1. Wear the ESD-preventive wrist strap and verify that the rack is well g

15 NOTE: Keep at least a distance of 1 U (44.45 mm, or 1.75 in) between devices for proper heat dissipation. Grounding the device WARNING! • Co

16 Figure 17 Grounding the device with the rack (1)

17 Figure 18 Grounding the device with the rack (2) { Grounding the device with a grounding conductor buried in the earth—If earth is available at

18 Installing a lightning protector for a network port A lightning protector is not provided with the device. H3C recommends that you install a light

19 Precautions If the performance of the port lightning protector is adversely affected in the following situations, follow the recommended solution:

20 Figure 21 Power strip with lightning protection (1) Operating LED (green) On means the circuit is operating properly. Off means the circuit is d

21 Figure 22 Connecting the console cable NOTE: • Identify the mark on the console port and make sure you are connecting to the correct port. •

22 Figure 23 Connection description 3. Select the serial port to be used from the Connect using list, and click OK. Figure 24 Setting the serial p

23 Figure 25 Setting the serial port parameters NOTE: To restore the default settings, click Restore Defaults. 5. Select File > Properties i

Preface The H3C WX5540E Access Controller Installation Guide describes preparing for installation, installing the access controller, troubleshooting,

24 Figure 27 Setting the terminal emulation in Test Properties dialog box Connecting the Ethernet cables Connecting a copper Ethernet port 1. Conn

25 • Make sure the Tx and Rx ports on a transceiver module are correctly connected. To connect the device to the network through an optical fiber: 1

26 3. Use a Phillips screwdriver to fasten the captive screws on the power module. Figure 29 Installing an AC power module Figure 30 Installing a

27 Figure 31 Connecting an AC power cord Connecting the DC power cord 1. Use a flat-blade screwdriver to remove the protection cover from the DC p

28 Verifying the installation Before powering on the device, verify that: • The correct power source is used. • The grounding cable is securely c

29 The main application file is self-decompressing... ...

30 Troubleshooting Power supply failure If the device cannot be powered on and the system status LED PWR is off, verify the following items: • The

31 Login password loss CAUTION: Dealing with console login password loss and user privilege level password loss from BootWare menus isdisruptive.

32 2. If the password recovery capability is disabled, select 5 from the BootWare menu to start the system with the factory default configuration.

33 For example, the software loading failures might occur in the following situations: • When you use XMODEM to load software, you select a baud ra

Obtaining documentation You can access the most up-to-date H3C product documentation on the World Wide Web at http://www.h3c.com. Click the links on t

34 Hardware management and maintenance The CLI and outputs depend on the software version that is running on the device. Logging in to the switching

35 CPLD 2 CPLD Version is 002 FPGA1 Logic Version is 108

36 ===== Current CPU usage info ===== CPU Usage Stat. Cycle: 10 (Second)

37 BootRom Ver : 1.01 CPLD Ver : 002 002

38 Field Description MAC_ADDRESS MAC address of the device. MANUFACTURING_DATE Manufacturing data of the device. VENDOR_NAME Vendor name. Displayi

39 Fan 1 State: Normal Fan 2 State: Normal

40 Step Command Remarks 2. Specify the exception handling method. system-failure { maintain | reboot } Optional. By default, the device reboots when

41 Appendix A Chassis views and technical specifications The figures in this document are for illustration only. Chassis views Figure 34 Front view

42 Power module views AC power module Figure 36 AC power module (1) Captive screw (2) Power switch (3) Air outlet vent (4) Power receptacle DC pow

43 Figure 38 SFP transceiver module Figure 39 SFP+ transceiver module Figure 40 Optical fiber with LC-type connectors (1) LC-type connector (2)

i Contents Preparing for installation ················································································································

44 Item Specification Memory 4 × 2 GB DDR3 Storage media 4 GB CF card Dimensions (H × W × D) (without rubber feet and mounting brackets) 88.1 × 440

45 Item Specification Receive sensitivity ≤ –30 dBm Saturation ≤ –14 dBm Table 16 SFP-FE-LX-SM1310-A specifications Item Specification Central wav

46 Item Specification Receive sensitivity ≤ –17 dBm Saturation ≤ –3 dBm Table 19 SFP-GE-LX-SM1310-A specifications Item Specification Central wave

47 Item Specification Receive sensitivity ≤ –21 dBm Saturation ≤ –3 dBm Table 22 SFP-GE-LH70-SM1550 specifications Item Specification Central wave

48 Item Specification Receive sensitivity ≤ –6.5 dBm Saturation ≤ 1.5 dBm Table 25 SFP-XG-LX-SM1310 specifications Item Specification Central wave

49 • GigabitEthernet 1/0/29 through GigabitEthernet 1/0/32—Internal interfaces that are used to connect the controller engine of the WX5540E.

50 Appendix B LEDs Panel LEDs Figure 41 LEDs (1) 100/1000Base-T autosensing Ethernet port status LEDs (2) 100Base-FX/1000Base-X SFP port status LEDs

51 LED Mark Status Description Expansion slot status LED (green/yellow) MOD Steady green An interface card is present. Flashing green The hard dis

52 Table 28 AC power module LED description LED Status Description AC OK Off No power is input or the power module has an input problem. Steady gree

53 Index A C D E G I L M P R S T V A Accessories,5 C Chassis views,41 Configuration terminal problems,30 Configuring the exception handling method,3

ii Software loading failure ··························································································································

1 Preparing for installation Safety recommendations Safety symbols When reading this document, note the following symbols: WARNING means an alert t

2 • Always check that the power has been disconnected when you perform operations that require the device to be powered off. Laser safety WARNING!

3 Table 2 Dust concentration limit in the equipment room Substance Concentration limit (particles/m3) Dust particles ≤ 3 x 104 (No visible dust on d